-->Skip to content
The MicroCut 45 DV is the newest machine added to the HTP lineup. What is new about this machine? CNC capabilities come standard, Dual Voltage machine, lighter weight, and an LCD Display!
We have thoroughly tested the MicroCut 45 DV on its precision and duty cycle. While running on 220V it will output a maximum 45 amps; on 110V it will output 25 amps. This machine is not approved for use with a generator. Hand cutting or CNC cutting this machine is sure to meet your expectations. Maximum severance cutting capacity is 1 inch, maximum quality cutting is 3/4".
With the MicroCut 45 DV, the maximum rated CNC pierce capacity is 1/2"; the cut speed at 1/2" material thickness runs at 16 IPM. To use your MicroCut 45 DV on your plasma table, simply install your CNC machine torch, plug in your table, and switch the cutter into CNC mode. The MicroCut 45 DV DOES NOT include the 14-Pin Mating Connector (P/N 64672).
**NOT APPROVED FOR USE WITH GENERATOR**
The MicroCut 45 DV packs powerful performance into a lightweight design. Thick or thin, the MicroCut 45 DV gets the job done! Backed by a 2-year warranty and a 30-day money back guarantee.
To get the best cutting capacity, fastest cutting speeds, and longest consumable life out of your CNC plasma cutting applications, we highly recommend using our HTP Max Dry desiccant air dryer system (P/N 25310-2). Dry air is a necessity when running a CNC with a torch height controller.
For torch consumables/parts, please visit the following page: MicroCut 45 DV Machine Torch Parts. And if you would like to purchase a hand torch, in addition to the machine torch, please visit the following page: MicroCut 45 DV Hand Torc Parts.
|Cutting Current||20 to 45 A|
|20 to 25 A|
|Open Circuit Voltage|
|Maximum CNC Cutting Capacity||½" @ 16 IPM|
|Quality Cutting Capacity||¾" @ 6.5 IPM|
|Severance Cutting Capacity||1" @ 4 IPM|
|Duty-Cycle (104 F)|
50% @ 45A
100% @ 32 A
40% @ 25 A
60% @ 27 A
100% @ 21 A
|Dimensions (Length x Width x Height)||18-3/4" x 6-¾" x 12-½"|
|Cutting Torch Length||20'|
|Input Power Cord Length||9'|
|Plasma/Cooling Gas Pressure||70 PSI|
|Plasma/Cooling Gas Volume||3.5 CFM|
This thing cuts as thick as my Hypertherm 45XP BUT the cut quality in nicer and consumables host 1/2 price .... ! Where it really shines is on my CNC table !!!! the cut quality - nothing short of amazing ! unless you use fine cut consumables on the HT45XP it can NOT keep up with the cut quality ! I can even run it on 110 when I am on the road.
So I’ve been using htp for quite a while now and I’ve always used there welders to weld everything in my shop so once I seen they had a plasma cutter I had to jump on it and order it and man was I surprised this thing cuts like butter literally everything I throw at it cuts right threw it definitely happy with my purchase and there customer service is top notch!!!!
I've been hunting for a plasma for years, and finally got my hands on one of the best units out there! The Microcut 45 DV was easy to set up and get started. My first project was cutting through 1/4” pipe and I was blown away by how quickly it sliced through it like butter. It’s so small and portable I can grab it and go just about anywhere. The torch is so light it doesn’t give me hand fatigue, and settings are easy to understand and adjust to what I need. I hope to get a CNC plasma table soon and use this unit for that. Very happy with this little machine and all my HTP machines!
Easy setup and it cuts like a dream
This plasma cutter was very quick and simple to set up following the well written instructions. This made setting up to cut a breeze. The cuts with this machine were fast and clean.